The areometer of the ABR-1M drilling mud (the Areometer of the ABR-1M) is designed to determine the density of drilling or any other solutions, as well as liquids and slurries neutral to polyethylene.   Instrument performance: – density measurement range, g/cm³ – with a calibrated load – ( 0.8 to 1.7 ) – without calibrated load…

The VBR-2 drilling mud viscometer (VBR-2 Viscometer) is designed to determine the conditional viscosity of drilling fluids used in the drilling of oil and gas wells and any wells for other purposes.   Instrument performance: – constant viscometer at a temperature of 20 ±5 °C, s – ( 15 ) – absolute error of constant viscometer,…

The rotational viscometer VSN-3M (Viscometer VSN-3) is designed to measure the rheological characteristics of visco-plastic bodies (drilling muds, paints, oil products, etc.), as well as to determine the dynamic viscosity of Newtonian fluids.   Specifications: Measurement range of static shear stress (SNS), n/m² (dy/cm²) – spring 1: 0-45 ( 0-450 ) – spring 2: 0-90 (…

The resistivity meter PR-1M is designed to measure the resistivity of drilling drilling fluids (solutions).   Instrument performance: – measurement range, Ohm-meter – from 0.01 to 10 – measurement range, °С – from +10 to +40 – device weight, kg – 2   It is applied according to: – RD 39-00147001-773-2004 “Methods of monitoring parameters of drilling mud”….

Device TEE-01M designed to measure the electrical stability of oil-based emulsion drilling fluids.   Instrument performance: – signal form – sinusoidal – output voltage range, V — from 0 to 2000 – peak output current, μA – 61 – rate of change of output voltage, V/s — 150 – weight of the device, kg – 2

Retort kit PH-10 (Retort PH-10) is designed to determine the percentage of solid phase, oil and water, as well as specifically for determining the oil content in emulsion drilling fluids. They are included in the set of equipment of the stationary and mobile laboratory for monitoring the quality parameters of drilling fluids. The volume of…

Retort kit PH-20 (Retort PH-20) is designed to determine the percentage of solid phase, oil and water, as well as specifically for determining the oil content in emulsion drilling fluids. They are included in the set of equipment of the stationary and mobile laboratory for monitoring the quality parameters of drilling fluids. The volume of…

Retort kit PH-50 (Retort PH-50) is designed to determine the percentage of solid phase, oil and water, as well as specifically for determining the oil content in emulsion drilling fluids. They are included in the set of equipment of the stationary and mobile laboratory for monitoring the quality parameters of drilling fluids. The volume of…

The FP-2 half-filter filter press (LPLT) is used to quickly determine the filtrate yield of drilling fluid in field and stationary conditions.   Instrument performance: – the volume of the test solution – 150 ml; – diameter of the filter – 54 mm; – pressure in the working chamber – 0.7 MPa; – overall dimensions –…

Filter press FP-2 standard cell (LPLT) is used to quickly determine the filtrate yield of drilling fluid in field and stationary conditions.   Instrument performance: – the volume of the test solution – 295 ml; – filter diameter – 90 mm; – pressure in the working chamber – 0.7 MPa; – overall dimensions – 200х525…

The FP-2 multi-section filter press (LPLT) is used to quickly determine the filtrate yield of a drilling fluid. 2, 4, 6-section filter press FP-2 is equipped with 2, 4 and 6 test cells at the request of the customer. A compressed gas cylinder is used as a source of pressure. Multi-section filter press FP-2 is…

The FP-3 HPHT175 high pressure and high temperature filter press is used for testing drilling fluids and oil well cements under conditions of increased pressure and temperature.   Instrument performance: – the volume of the test solution – 175 ml; – pressure in the working chamber – 4.14 MPa; – pressure in the filtrate collection…

The FP-3 HPHT500 high pressure and high temperature filter press is used for testing drilling fluids and oil well cements under conditions of increased pressure and temperature.   Instrument performance: – the volume of the test solution – 500 ml; – maximum temperature of the heating chamber – up to +250 ºС – maximum pressure in the…

Ceramic Filter Discs for HPHT Filter Press   Characteristic: — Disc thickness, mm — 6.5 ±0.3 — Disc diameter, mm — 63 ±0.2   Pore sizes, microns: 2       10       50 3       12       55 4       20       80 5       40       120…

Lever balance – VRP-1M densitometer is designed to measure the density of drilling, cement mortars and liquid chemicals. Scales can be used both indoors and outdoors under a canopy, in areas with a temperate climate.   Instrument performance: – Measuring range, g/cm³ from 0,8 to 3,0 – Graduation, g/cm³ – 0,01 – Measurement error, % ±0,5…

The scales lever sealed VRG-2M are intended for measurement of density of drilling, cement mortars and liquid chemical reagents under pressure. The test solution is pumped into the glass under pressure, which brings the conditions closer to the downhole.   Instrument performance: – Measuring range, g/cm³ from 0,8 to 3,0 – Graduation, g/cm³ – 0,01 –…

Thermo glass TV-2 (Thermocup TV-2) is used for heating drilling or cement slurries.   Instrument performance: – device power supply, V – 220 – power consumption, W – 300 – maximum operating temperature, °С – 100 – sample heating time, min – 30 – overall dimensions, mm – 190х125х120 – device weight, kg – (2.1)  …

Calcimeter KM-2 is designed for rapid determination of the content of calcite (calcium carbonate) and dolomite (magnesium carbonate) in samples of core and sludge. This method is used to determine the concentration of calcium carbonate in the drilling fluid.   Instrument performance: – capacity, cm ³ – ( 188 ) – pressure, MPa – (…

The kit is intended for the operational determination of the sand content in the drilling mud. Completeness: – 63.5 mm strainer; – funnel; – plastic tube 0-20%; – rinsing 500 ml .; – case.   It is applied according to: – GOST 33213-2014 (ISO 10414-1: 2008) “Water based drilling fluids”. – GOST 33697-2015 (ISO 10414-2: 2011)…

The aging cell allows samples to be exposed to temperatures above the boiling point, while maintaining them in a liquid state. They can also be exposed to temperatures in static conditions or in dynamic conditions.   Instrument performance: – cell volume, ml. – 350, 500; – maximum working temperature, ºС – 260; – maximum pressure,…

The ST-2 stalagmometer is designed to determine the surface tension of surfactant solutions by determining the volume of droplets that are extruded at the boundaries: solution-surfactant-anti-polar liquid or solution of surfactant-air.   Instrument performance: – Micrometric feed division price, mm – 0,01 – Power supply of the device, V 220, Hz 50 ±1 – Overall dimensions,…

The ST-2M digital stalagmometer is designed to determine the surface tension of surfactant solutions by determining the volume of droplets extruded at the boundaries: solution-surfactant-antipolar liquid or surfactant-air solution.   Instrument performance: – Micrometric feed division price, mm – 0,001 – Power supply of the device, V 220, Hz 50 ±1 – Overall dimensions, mm –…

The KTK-2.01 manual version is designed to determine the coefficient of friction of the filter cake of drilling drilling fluid in the conditions of field laboratories and at drilling sites in order to identify the effectiveness of lubricating additives and surgical intervention in the drilling process in difficult conditions.   Instrument performance: – angle of…

The KTK-2.02 device with an electric drive is designed to determine the coefficient of friction of the filter cake of drilling drilling fluid in the conditions of field laboratories and at drilling sites in order to identify the effectiveness of lubricating additives and surgical intervention in the drilling process in difficult conditions.   Instrument performance:…

The KTK-2.03 device with a digital angle reader is designed to determine the coefficient of friction of the filter cake of drilling drilling fluid in the conditions of field laboratories and at drilling sites in order to identify the effectiveness of lubricating additives and surgical intervention in the drilling process in difficult conditions.   Instrument…

The VM-6M device is designed to determine the filtration rate (loss of water) of clay solutions used in drilling oil and gas wells.   Instrument performance: – measuring range of filtrate volume, cm³ – ( 0-40 ) – actual diameter of the filter, mm – ( 53 ) – scale division price, cm³ – (…

The device SNS-2M is designed to measure the maximum static shear stress of drilling fluids. It is used in the oil and gas industry in field laboratories.   Instrument performance: – limits of measurements, mg/cm² – with a thread diameter of 0.3 mm – ( from 4 to 30 ); – with a thread diameter…

The device VIKA IV-2 is designed to determine the normal thickness, setting time and determine the thickness of the crust of cement paste.   Instrument performance: – needle diameter, mm – ( 1.13 ±0.05 ) – length of the needle working part, mm – ( 50 ±1 ) – pestle diameter, mm – ( 10…

Cone spreadability КР-1 (Cone КР-1) is designed to determine the spreadability of cement mortar in indoor heated dry premises.   Instrument performance: – the minimum diameter of the concentric circle, mm – ( 72 ) – maximum diameter of concentric circle, mm – ( 250 ) – distance between the circles of the cone, mm…

Pycnometer P-1 is designed to determine the density of cement mortar.   Instrument performance: – Capacity of pycnometer within, cm³ – ( 100 ±5 ) – Overall dimensions, mm – ( 41×122,5 )   It is applied according to: – GOST 26798.1-96 “Cement grouting. Test methods”.

The PKN-2 device is designed to determine the swelling ratio of clays.   Instrument performance: – overall dimensions, mm – ( 60x85x415 ) – indicator dividing price, mm – ( 0.01 ) – the working stroke of the indicator rod, mm – ( 11,5 ) – weight, kg – ( 0.7 )

OM-2 metal sump (OM-2 sump) is designed to determine the percentage of sand, as well as washed sand in a sample of the mud. Instrument performance: – sump capacity, cm³ – ( 500 ±15 ) – test tube capacity, cm³ – ( 10 ) – cup capacity, cm³ – ( 50 ±1 ) – the…

The stability cylinder CS-2 (cylinder CS-2) is designed to determine the index of stability of the drilling fluid.   Instrument performance: – capacity, ml. – (700 ±5)   It is applied according to: – RD 39-00147001-773-2004 “Methods of monitoring parameters of drilling mud”. – STO Gazprom 7.3-002-2010 “Regulatory documents for the construction of wells. Drilling fluids. Field…

The KC-5 Consistometer is designed to determine the solidification time of cement slurry during cementing of oil and gas wells with temperatures up to 95 C.

Laboratory mixer LMR-1 will be required for mixing cement, cement and other solutions. Creation of test samples.

The device PGR-1 for monitoring the gas content of drilling fluids is intended for the operational control of the gas phase of drilling fluids. Scope: in the circulating system of drilling rigs. Premises and open drilling sites in temperate climates.   It is applied according to: – RD 39-00147001-773-2004 “Methods of monitoring parameters of drilling mud”….